Plumbers NZ is New Zealand's largest online plumbing, gas and drainage resource. Plumbing exam help, plumbing news, directory and free quotes.

« Older Plumbing | Strength needed to be a Plumber »
Pages: [1]   Go Down

Author Topic: Water supply - 50m run  (Read 3642 times)

0 Members and 1 Guest are viewing this topic.

Offline Dean

  • Jr. Member
  • **
  • Posts: 4
  • Karma: +0/-0
Water supply - 50m run
« on: March 03, 2009, 10:25:39 PM »
Hi there, I'm wanting to run a 50m pipe to supply a 1 bedroom, 1 bathroom house. I'm on bore water, and have a pressure tank set up (I think about 200 to 300kpa, or 30 to 45psi). There's a gradual elevation of about 2 metres over this distance. I can connect to a 32mm spare outlet from the pressure tank. To obtain the best pressure and water flow, how would I go about the pipe sizes? Starting at 32mm, over what distances should I reduce the pipe sizes gradually? Am planning on just running alkathine pipe. Appreciate any advice.

Linkback: https://www.plumbers.nz/ask-plumbers-public/2/water-supply-50m-run/156/
Share Post | Report to moderator   Logged

Offline worker

  • Jr. Member
  • **
  • Posts: 20
  • Karma: +3/-0
Re: Water supply - 50m run
« Reply #1 on: March 04, 2009, 12:31:15 PM »
the type of pump you are using is a very important factor as that determines the volume supplied and the pump curve (pumps lose their effect over long distances dependant on tpye), however, google 'boxes formula', this is used for calculating  diameters of supply pipes. If that crazy calculation throws you
Then reckoning can be used. I reckon with my almost expert opinion (been Qualified 22 years) run the largest dia. you can ie; 32 all the way, if not then 1x25m  roll of  32mm and 1 25m roll of 25mm the cost difference between 25 and 32 aint that great from your rural supply merchant, they're often cheaper than plumbins supply merchants. p.s. if you oversize now you will be able to increase the size of you house later.
Share Post | Report to moderator   Logged

Offline Dean

  • Jr. Member
  • **
  • Posts: 4
  • Karma: +0/-0
Re: Water supply - 50m run
« Reply #2 on: March 04, 2009, 09:23:14 PM »
Hi there, thanks for your quick reply. The pump I'm using is a 3 1/2h Davies. If you're in the Auckland area, I wouldn't mind any ideas on who would be well priced for purchasing alkathene piping. Cheers for the suggestions, will look into 32mm alkathene.

Quote from: worker on March 04, 2009, 12:31:15 PM
the type of pump you are using is a very important factor as that determines the volume supplied and the pump curve (pumps lose their effect over long distances dependant on tpye), however, google 'boxes formula', this is used for calculating  diameters of supply pipes. If that crazy calculation throws you
Then reckoning can be used. I reckon with my almost expert opinion (been Qualified 22 years) run the largest dia. you can ie; 32 all the way, if not then 1x25m  roll of  32mm and 1 25m roll of 25mm the cost difference between 25 and 32 aint that great from your rural supply merchant, they're often cheaper than plumbins supply merchants. p.s. if you oversize now you will be able to increase the size of you house later.
Share Post | Report to moderator   Logged

Offline kiwichris

  • Jr. Member
  • **
  • Posts: 29
  • Karma: +3/-0
Re: Water supply - 50m run
« Reply #3 on: May 02, 2009, 01:40:01 AM »
It's a bit of a wary situation

Personally, I'd advise against doing ANY plumbing work if you are not a craftsman plumber or register D/L

You could get in a lot of trouble with the council!
Share Post | Report to moderator   Logged
Born to fish - forced to work!
Pages: [1]   Go Up
« Older Plumbing | Strength needed to be a Plumber »

* Share Topic

Share via digg Share via facebook Share via linkedin Share via twitter

Similar Topics

  Subject / Started by Replies / Views Last post
clip
Alternative firefighting water supply SNZ PAS 4509:2008

Started by Enn

0 Replies
2041 Views 		Last post November 22, 2014, 03:49:59 PM
by Enn
xx
Replacing galvanized pipe main supply and water pressure

Started by toycollector10

21 Replies
14386 Views 		Last post April 13, 2013, 07:39:06 AM
by Rodza1
xx
Gas meters, KW or MJ supply rating

Started by newguy

9 Replies
10096 Views 		Last post November 16, 2012, 11:13:53 AM
by newguy
xx
hot water cylinder overflow continuously and water is not hot at all

Started by jerrine

4 Replies
14522 Views 		Last post September 06, 2010, 09:09:49 PM
by jobby
 
Share this topic...
In a forum
(BBCode)
In a site/blog
(HTML)