Plumbers NZ is New Zealand's largest online plumbing, gas and drainage resource. Plumbing exam help, plumbing news, directory and free quotes.

« What did everyone think of the 9192 paper? | Craftsman Gasfitting Exam »
Pages: [1]   Go Down

Author Topic: certifying exam ?? Is this right  (Read 4512 times)

0 Members and 1 Guest are viewing this topic.

Offline sharks

  • Jr. Member
  • **
  • Posts: 5
  • Karma: +0/-0
certifying exam ?? Is this right
« on: April 28, 2011, 11:11:27 PM »
Please help me out here. As far as i know you cant do what theyve done in this question. Please , if im wrong , can you tell me where I can find it in as/nzs 3500.

Q 17 in nov certifying exam asks you to draw in the drains.  http://www.pgdb.co.nz/~downloads/9195Q%20November%202010.pdf (thats the link to the Q , just scroll down)

The answer that they give ,  http://www.pgdb.co.nz/~downloads/9195A%20Nov%202010.pdf  (the answers they give , scroll down to 17)
 With elavated drainage , min size is 65mm and they are running 40mm , so they cant be using that.
 Under the single stack system with 1 section of floor graded (8.8.5 as/nzs 3500) everything must enter the main drain individually   and if not must be vented.Theyve got a WC and basin combined , so surely cant be that.

Thanks guys

Linkback: https://www.plumbers.nz/plumbing-gas-fitting-and-drainlaying-apprentice-support/3/certifying-exam-is-this-right/634/
Share Post | Report to moderator   Logged

Offline Plumber

  • Administrator
  • Hero Member
  • *****
  • Posts: 736
  • Karma: +52/-2
  • ***#1 Plumber***
Re: certifying exam ?? Is this right
« Reply #1 on: April 29, 2011, 06:53:16 PM »
Just answering by memory here and on the fly : Anything "not underground" is considered a drain, where as anything inside the ground is considered a sewer, So the rule min 65 only applies to a sewer. When you do an underslab and have a foorwaste, you can charge that floorwaste with a 50mm pipe (also considered drain) after the floorwaste it has to be 65mm (considered sewer). Then you can calculate the drainpipe size by using your fixture units. Hope this helps!  ;D
Share Post | Report to moderator   Logged
Please note that the advice I am giving is only my opinion and not necessarily a fact.  Please refer to our terms and conditions.

Offline Plumber

  • Administrator
  • Hero Member
  • *****
  • Posts: 736
  • Karma: +52/-2
  • ***#1 Plumber***
Re: certifying exam ?? Is this right
« Reply #2 on: April 29, 2011, 06:54:58 PM »
The only mistake I see is the 60mm LOL
Share Post | Report to moderator   Logged

Offline sharks

  • Jr. Member
  • **
  • Posts: 5
  • Karma: +0/-0
Re: certifying exam ?? Is this right
« Reply #3 on: April 29, 2011, 08:01:18 PM »
hey karma , thanks for your response. In the modal answer that they give they have a 40mm discharge pipe connecting into the main suspended drain so I dont think theyre using drainage princibles. Just not sure what rule they are applying to this system. I have contacted  Jose at the board and he reckons he will forward it on the the appropriate person. See how we go!!!!
Cheers
Share Post | Report to moderator   Logged

Offline TS

  • Full Member
  • ***
  • Posts: 145
  • Karma: +18/-99
Re: certifying exam ?? Is this right
« Reply #4 on: June 04, 2011, 09:59:37 AM »
I think the drawing is wrong also. They also state gradients of 1:60. This is too flat for 40mm and 50mm.
Share Post | Report to moderator   Logged

Offline TS

  • Full Member
  • ***
  • Posts: 145
  • Karma: +18/-99
Re: certifying exam ?? Is this right
« Reply #5 on: July 01, 2011, 05:39:59 PM »
How have you gotten on with this?
Share Post | Report to moderator   Logged
Pages: [1]   Go Up
« What did everyone think of the 9192 paper? | Craftsman Gasfitting Exam »

* Share Topic

Share via digg Share via facebook Share via linkedin Share via twitter

Similar Topics

  Subject / Started by Replies / Views Last post
xx
Getting rid of Certifying Common exam

Started by woody

2 Replies
2767 Views 		Last post October 19, 2011, 10:43:40 PM
by TS
xx
certifying nov 2012 exam

Started by pugsy

14 Replies
7464 Views 		Last post March 07, 2013, 08:28:26 AM
by robbo
xx
Certifying Exam papers 11&12

Started by Shoreside

3 Replies
2636 Views 		Last post July 18, 2013, 10:59:39 PM
by MikeJason
xx
ahhhh gas certifying exam study

Started by roberto

1 Replies
3195 Views 		Last post August 20, 2014, 05:58:32 PM
by Jaxcat
 
Share this topic...
In a forum
(BBCode)
In a site/blog
(HTML)


Auckland Painters