Plumbers NZ is New Zealand's largest online plumbing, gas and drainage resource. Plumbing exam help, plumbing news, directory and free quotes.

« knowing the latest tank flush kits-better than fluidmaster, geberit | Aquatight wall caddy's what a waste of time »
Pages: [1]   Go Down

Author Topic: valves on ballcock lines  (Read 4969 times)

0 Members and 1 Guest are viewing this topic.

Offline 15mmhexnipple

  • Jr. Member
  • **
  • Posts: 14
  • Karma: +0/-0
valves on ballcock lines
« on: July 05, 2010, 07:30:21 PM »
as a plumber id like to see a valve in a ceiling on the line to the ballcock in a header tank, i have been told by another plumber that this is "lazy plumbing", i believe that should be a requirement for the 15mm line to the ballcock, would save time turning the whole house's water supply off,

what do you think?????

Linkback: https://www.plumbers.nz/plumbing/1/valves-on-ballcock-lines/428/
Share Post | Report to moderator   Logged

Offline TS

  • Full Member
  • ***
  • Posts: 145
  • Karma: +18/-99
Re: valves on ballcock lines
« Reply #1 on: July 05, 2010, 07:45:36 PM »
I personally agree. There is no requirement however. Interestingly enough everyone puts one on a WC but their not required there. I think its good trade practice to put them on ballcock lines.
Share Post | Report to moderator   Logged

Offline 15mmhexnipple

  • Jr. Member
  • **
  • Posts: 14
  • Karma: +0/-0
Re: valves on ballcock lines
« Reply #2 on: July 05, 2010, 07:50:45 PM »
i also think that line strainers are a good point too, although i always use pyrmid filters
Share Post | Report to moderator   Logged

Offline hefzibah

  • Jr. Member
  • **
  • Posts: 19
  • Karma: +1/-0
Re: valves on ballcock lines
« Reply #3 on: July 05, 2010, 08:39:34 PM »
you have to install a serve valve........
Share Post | Report to moderator   Logged

Offline TS

  • Full Member
  • ***
  • Posts: 145
  • Karma: +18/-99
Re: valves on ballcock lines
« Reply #4 on: July 14, 2010, 11:08:52 PM »
Quote from: hefzibah on July 05, 2010, 08:39:34 PM
you have to install a serve valve........


Where does it say that?
Share Post | Report to moderator   Logged

Offline GMcT

  • Jr. Member
  • **
  • Posts: 14
  • Karma: +0/-0
Re: valves on ballcock lines
« Reply #5 on: August 21, 2010, 05:58:32 PM »
Its recommended, but not a must. I personally think they should go in. Saves time trying to find the old "buried toby".
Share Post | Report to moderator   Logged

Offline hefzibah

  • Jr. Member
  • **
  • Posts: 19
  • Karma: +1/-0
Re: valves on ballcock lines
« Reply #6 on: September 21, 2010, 02:56:33 PM »
Quote from: Mike H on July 14, 2010, 11:08:52 PM
Quote from: hefzibah on July 05, 2010, 08:39:34 PM
you have to install a serve valve........


Where does it say that?


AS/NZS 3500 , who uses the old school part of G12
Share Post | Report to moderator   Logged
Pages: [1]   Go Up
« knowing the latest tank flush kits-better than fluidmaster, geberit | Aquatight wall caddy's what a waste of time »

* Share Topic

Share via digg Share via facebook Share via linkedin Share via twitter

Similar Topics

  Subject / Started by Replies / Views Last post
xx
reducing valves

Started by leaky

5 Replies
3825 Views 		Last post September 10, 2011, 09:29:50 AM
by roberto
xx
H2OT HWC & valves

Started by woody

9 Replies
5239 Views 		Last post December 23, 2012, 10:28:14 PM
by integrated
xx
Tempering valves

Started by ptopnz

21 Replies
8758 Views 		Last post October 16, 2013, 08:45:55 PM
by bowtieboy
xx
Hepvo Valves

Started by spud

5 Replies
2563 Views 		Last post August 21, 2015, 06:26:38 PM
by integrated
 
Share this topic...
In a forum
(BBCode)
In a site/blog
(HTML)