Plumbers NZ is New Zealand's largest online plumbing, gas and drainage resource. Plumbing exam help, plumbing news, directory and free quotes.

Author Topic: what's good water pressure coming from the street?  (Read 2102 times)

0 Members and 1 Guest are viewing this topic.

Offline hattricknz

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
  • Im new @ Plumbers NZ!
what's good water pressure coming from the street?
« on: October 11, 2016, 08:58:41 AM »
Hi there

What is good pressure to have coming from the street? Ours was abour 9bar and a plumber put on a PRV(pressure reducing valve) which got it down to 4/5bar.

Some backgorund. Plumber was around to do other work and offered this as a solution. but now the cold pressure in the sink is noticeably lower now and think I want it back to the old pressure or at least higher then what it is now.

Can anyone advise on good pressure to have coming in from street and what pressures should be at kitchen tap for example? what are the standards in NZ? Tried the BRANZ site there but not sure it that is the place to look. tks



Linkback: https://www.plumbers.nz/plumbing/1/whats-good-water-pressure-coming-from-the-street/2039/

Offline robbo

  • Hero Member
  • *****
  • Posts: 1259
  • Karma: +83/-7
Re: what's good water pressure coming from the street?
« Reply #1 on: October 11, 2016, 02:33:29 PM »
Hi, most new installs pressure limiting valves which are preset to 500kpa and can be adjusted to the pressure that you like. A pressure reducing valve is used for low pressure hot water so will reduce the cold down to far if is put on the incoming mains. A limiting valve on the mains will be able to reduce the pressure to the required setting,cheers

Offline integrated

  • Sr. Member
  • ****
  • Posts: 412
  • Karma: +37/-2
Re: what's good water pressure coming from the street?
« Reply #2 on: October 11, 2016, 07:24:30 PM »
Hi there

What is good pressure to have coming from the street? Ours was abour 9bar and a plumber put on a PRV(pressure reducing valve) which got it down to 4/5bar.

Some backgorund. Plumber was around to do other work and offered this as a solution. but now the cold pressure in the sink is noticeably lower now and think I want it back to the old pressure or at least higher then what it is now.

Can anyone advise on good pressure to have coming in from street and what pressures should be at kitchen tap for example? what are the standards in NZ? Tried the BRANZ site there but not sure it that is the place to look. tks



this really depends on you're hot water cylinder/boiler and tapware - alot of cylinders and heating appliances dont like inlet pressures above 500kpa - 5bar - the same goes for tapware and both will be warranty void if going over stated operating pressures


900kpa - 9bar is way too high and not good for system longevity anyway - the plumber done the right thing


Share via digg Share via facebook Share via linkedin Share via twitter

Similar Topics

  Subject / Started by Replies / Views Last post
xx
Hot water backfeeding to the street

Started by fluffitt

1 Replies
1948 Views
Last post November 03, 2011, 06:41:33 PM
by Thunderhead
xx
more water pressure

Started by bell

4 Replies
5003 Views
Last post June 15, 2012, 08:04:43 PM
by integrated
xx
Low hot water pressure

Started by namelsss

8 Replies
9955 Views
Last post March 12, 2011, 06:58:10 PM
by Thunderhead
xx
water pressure

Started by kat

15 Replies
10640 Views
Last post April 18, 2011, 08:48:02 PM
by kat
 
Share this topic...
In a forum
(BBCode)
In a site/blog
(HTML)